Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateTrusted Garage Door Repair for Yonkers Homeowners
A garage door that won’t open traps your car, and one that won’t close leaves your home open. Garage door repair in Yonkers starts at a typical $150-$600 depending on what’s actually wrong, and we can usually diagnose and fix it the same day. Our technicians have up to 13 years of experience and work only on garage doors, so they’ve seen the failure before you finish describing it. We service LiftMaster and Chamberlain openers, Clopay, Amarr and Wayne Dalton doors, and much more. Garage doors are all we do. Call (844) 443-4494 and we’ll get a trained technician out to you.
What Our Garage Door Repair Service Includes
We handle the whole range of residential garage door failures, from a simple roller swap to a snapped spring that has your door sitting crooked in the frame. Here’s what each repair involves and when you’re likely to need it.
Panel Replacement
A damaged panel is a single section of the door, not the whole thing, and replacing just that section is usually far cheaper than a new door. You need it after a car backs into the door, after a hard impact, or when a panel has rusted through or separated at the seams. We match the panel to your existing door’s profile and color where the brand still makes it, and when a match isn’t available we tell you that upfront so you can weigh a partial fix against replacement.

Spring Repair
Torsion and extension springs carry the full weight of the door, so a broken spring is the most dangerous thing that can go wrong with a garage door. You need spring work when the door won’t lift, feels suddenly heavy, or you hear a loud bang from the garage and find the door stuck. Our technicians handle spring repair as a named specialty, and we never suggest a homeowner tackle it personally, because the tension involved can cause serious injury to someone without the right tools and training.

Cable Repair
Cables run from the bottom corners of the door up to the drum, and they do the lifting alongside the springs. You need cable repair when a cable has frayed, kinked, slipped the drum, or snapped, which usually leaves the door hanging off one side. We replace the damaged cable and check the opposite side, since cables tend to wear at the same rate, then reset the door so it travels level again.

Track Realignment
The tracks are the metal rails the door rides in, and when one gets bent or knocked out of plumb, the door binds, scrapes, or stops halfway. You need realignment after a bump with a car, a door that jumped the track, or a slow drift over time from the house settling. We straighten the rails, check the spacing along their full length, and confirm the door rolls cleanly before we call it done.
Roller Replacement
Rollers are the small wheels that guide the door through the track, and worn rollers make a door noisy, jerky, or hard to lift. You need them replaced when the door squeals, vibrates, or the rollers have flat spots from years of use. We swap the worn rollers, and if the hinges are loose too, we tighten them in the same visit so the door runs quietly again.
Sensor Calibration
The safety sensors sit at the bottom of the tracks and reverse the door when something crosses the beam, and a misaligned or dirty sensor stops the door from closing. You need calibration when the door starts to close and then reverses, or when the opener light blinks and nothing moves. We align the sensors, clear the lenses, and test the reversal so the door responds the way it should.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Brands We Service for Garage Door Repair
We work on the brand already in your garage. LiftMaster openers are the most common we see in Yonkers, and our technicians know their limit settings, battery-backup behavior, and the myQ connection points well enough to diagnose without guessing. Wayne Dalton doors have their own panel and spring geometry that trips up a generalist, and we’ve worked with those enough to know where they wear and what a proper repair looks like. We also service Chamberlain, Genie, Clopay, Amarr, Craftsman and Raynor equipment, each with its own quirks in the hardware.
Familiarity with the hardware matters on repair calls. A Craftsman opener that won’t reverse is often a sensor or travel-limit problem rather than a motor failure, and a Raynor door that sags usually has a spring or cable issue rather than a bent track. We diagnose the actual cause instead of swapping parts and hoping. For a bigger failure, our garage door repair page covers the wider scope of what we fix. Whether you have a LiftMaster, a Wayne Dalton, or any other make, we can help.
Signs You Need Garage Door Repair Right Now
Some garage door problems can wait a day or two. Others should get a call the same day, because a failing door can fall, jam, or leave your home unsecured. Here’s what to watch for.
- The door won’t open or won’t close. If the opener runs but the door doesn’t move, or the door moves a few inches and reverses, something in the lifting mechanism or the safety sensors has failed. A door stuck open overnight is a security problem, so get this looked at quickly.
- A loud bang from the garage. A torsion spring breaking sounds like a firecracker or a car backfiring. Once it goes, the door is held up by the opener alone, which isn’t designed for that weight, so stop using the door and call for spring repair.
- The door looks crooked or hangs low on one side. Uneven lifting usually points to a stretched or snapped cable, or a spring that has lost tension on one side. Running the opener on a crooked door can bend the tracks and turn a smaller repair into a bigger one.
- Grinding, squealing, or scraping as it moves. Worn rollers or a track that’s out of alignment cause noise and drag on the opener. Left alone, the extra strain shortens the opener’s life and can crack the panels.
- The door reverses on its own when closing. When the safety sensors are misaligned, dirty, or failing, the door won’t close properly, and the opener may be fighting a blocked beam. This one is worth a quick check, and worth a technician’s look if it keeps happening.
Our Garage Door Repair Process – Step by Step
- 1
Take the call and book the visit. You describe what’s happening, and we ask the questions that tell us what tools and parts to bring. When your door is stuck, we aim to get a technician to you the same day, and we answer the phone 24/7.
- 2
Diagnose on site. A technician checks the springs, cables, tracks, rollers, and the opener as one system rather than looking only at the obvious symptom. A grinding door is sometimes a roller problem and sometimes a sign the door is off balance, and a proper diagnosis finds the difference.
- 3
Explain the findings and quote the price. You get a clear description of what’s worn, what’s broken, and what isn’t, plus a written price for the work before anything begins. We don’t start work until you’ve agreed to the quote.
- 4
Do the repair. The technician replaces the failed components, adjusts the door so it balances and travels evenly, and tests the opener, safety sensors, and reversal settings once the fix is in place.
- 5
Walk you through it and leave the garage clean. You get a run-through of what was done and what to watch for down the road, and the technician cleans up before leaving. If we found a problem we didn’t fix, we tell you so you can plan for it.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Garage Door Repair Cost in Yonkers?
Most garage door repairs in Yonkers fall between $150 and $600, and the exact figure depends on which part failed and how much the door has been affected. A typical spring repair runs $180-$340, and that’s for one spring; a matched pair is usually replaced together, so a pair costs about twice that range. Cable repair runs $130-$250, opener repair $120-$320, panel replacement $250-$500, and track realignment $120-$240. Roller replacement runs $110-$220 and sensor calibration is often the smallest job of the bunch.
What affects the price:
- Which parts need replacing. A roller swap is a small job; a spring, cable, and track repair done together costs more but saves you a second visit.
- Door type and brand. Common door styles and widely made panels cost less to match than an older or less common model.
- Whether a second problem turns up. We quote the work we find, and we tell you what’s optional before touching it.
To avoid overpaying, get the diagnosis in writing and ask what’s actually broken rather than accepting a blanket recommendation to replace the door. Our estimate is free, and the written estimate sets the final price, so the number we agree on is what you pay. Full pricing detail sits on our garage door spring repair page if a spring is your problem. Call (844) 443-4494 for a free estimate.
Garage Door Repair Near Yonkers – Our Service Area
We cover Yonkers and the surrounding Westchester communities, including Eastchester, Hastings-on-Hudson, Dobbs Ferry, Hartsdale, Scarsdale, Crugers and Greenville, plus over into Rockland and Bergen with Montebello, Wesley Hills, Suffern and Sloatsburg. For doors closer to Yonkers itself, we aim for the same day. Neighbors in the outlying areas can check our garage door repair and garage door repair pages for those areas.
Serving Yonkers, NY – Our Local Coverage Area
We serve Yonkers and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Garage Door Repair in Yonkers
Garage door repair is fixing the specific part that has failed on your door or opener, rather than replacing the whole system. That covers springs, cables, tracks, rollers, panels, sensors, and the opener itself. We diagnose the cause first, so you’re paying to fix the actual problem and not a guess.
Most repairs take between one and three hours on site, depending on the part. A roller replacement or sensor calibration is often under an hour, while a spring or cable replacement takes longer because the door has to be reset and tested. We give you a realistic time when we quote the job.
A typical garage door repair in Yonkers runs $150-$600, with spring repair at $180-$340 for one spring, cable repair at $130-$250, and opener repair at $120-$320. The written estimate sets the final price, and there’s no charge for the estimate. Call (844) 443-4494 for an exact quote.
Yes, we service LiftMaster and Wayne Dalton equipment, along with Chamberlain, Genie, Clopay, Amarr, Craftsman and Raynor. Our technicians work with those brands regularly and know their failure points. Tell us the brand and model when you call and we’ll confirm what the visit needs.
Same-day service is often available for urgent repairs, so call and we’ll book the earliest opening. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Repair requests get priority over bigger jobs, and for a failed door our emergency garage door page explains how that works.
Warranty terms depend on the part and the repair, and we explain the coverage on your specific job before you agree to the work. We don’t offer a single blanket promise, because a spring and a sensor call are very different repairs. Ask us at the quote and we’ll tell you exactly what’s covered.
Clear the floor in front of the door and the space between the cars so the technician can work and test the door safely. Unlock the garage door if it has a manual lock, and let us know which car stays or moves so we don’t block it in. If the door is stuck open, don’t try to force it down; park the car outside and we’ll take it from there.
Schedule Your Garage Door Repair Service in Yonkers Today
When your door won’t move, we will. Call (844) 443-4494 to book a garage door repair in Yonkers and get a technician out to diagnose the problem, quote the price, and fix it right the first time. Our estimate is free, the price is set before any work starts, and we stand behind what we do. From spring to opener to the full door, one call covers it. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Yonkers Garage Door Repair Co.